Building a Stainless Steel Shower Stall

showerI decided that I wanted a stainless steel shower in our new house. I’d installed enough tile and fiberglass showers over the years to turn me off both applications forever. Stainless steel would be long-lasting, worry-free if you don’t mind water spots, and cool/different. The house has a few industrial touches in it and this seemed like a fit.

As it turned out, we don’t see many stainless steel showers in the U.S. other than in jails and vintage travel trailers. The price for a standard size stainless steel stall made in the U.S. is about $8,000. Choke. Meanwhile the option for anything standard was out since I made the space extra wide and tall and the drain slightly off-center for reasons I won’t go into here. The price would be even higher!

So I drew up a plan and took it to a local metal fabricator: Mid Valley Metals in Eugene, Oregon. After all, it’s just three walls and a base, and metal isn’t that expensive.

They would manufacture the walls and base from 16-gauge stainless steel with a mill (factory) finish. The wall tops would extend to the 9-foot ceiling and the base edge would be flush with the tile floor. Trim for the top and sides would also be provided. Mid Valley would plasma cut holes for the fixtures and suggested they also cut holes for the screws so that I wouldn’t be wearing out drill bits on that hard stainless steel. The extra cost was nominal and saved me a lot of time and frustration. As it turned out, the price would be $1,600. That was less expensive than a good quality fiberglass unit, plus it would be my custom-sized stainless steel shower!

They sent out a guy to verify the measurements, which agreed with mine but it didn’t hurt to double-check. I indicated where the fixtures would be and ordered an extra face plate for the shower handle, as the one it came with was cheesy looking.

To note, we found the fixtures on Amazon and eBay from reputable sellers who charged about 1/3 of retail. Fixtures, including light and plumbing, seem to be some of the most overpriced items you’ll contend with for a house project. I encourage you to shop around, even look for used stuff. It can take patience, but if you have a tight budget and the extra time (or a spousal unit who loves bargains), you can save a lot of money.

While Mid Valley Metals built the parts, I did the prep work. My shower space is 42 x 36 inches, the insulated walls are 2×6 framing with a vapor barrier and 1/2 inch sheetrock. The floor is concrete slab. I installed a layer of 1/2 inch thick cement board and a 1/4 inch thick fiber cement board. Both were preventative measures in case water gets behind the sheet metal, which is unlikely, plus they provided a firm base for the wall panels to bond to.

The building code requires a 1/4 inch-per-foot drop for a shower base, which was accomplished in the manufacturing process by creasing the metal in the base from corners to drain.

BasePhotosMy walls weren’t perfectly plumb, so the metal would not lay as flat as it should. I made a fairly elaborate shimming system using felt paper, 30 and 15 pound, that was bonded using a super flexible sealant. By the time I was done, the walls were plumb in the corners and for the most part had a flat surface on all three sides for the metal to rest on. I used leveler to bring up the floor a bit and make sure it was level. Then I used more shims to account for the drop.

Now it was time to put it all together. The base went in first. I had Mid Valley Metals make 4 inch walls for the surround edges. That’s more than needed, since the step out of the shower is just 1 inch, but it’s what I did. Note the drain is dimpled. This was because the only shower drains I could find, locally and online, were for tile application. They set up higher than necessary for sheet metal. The dimple made it so the drain would set down low enough not to puddle.

panelsMy neighbor helped install the back and walls. First I applied the glue, then we fit the metal into place. I bought some heavy duty locking suction cups that worked great for the chore. But beware, they can fail sometimes, so don’t have a foot under the metal while depending on them to hold it up!

We installed the back wall first (which was the heaviest) and used pressure sticks to hold it in place, allowing the glue to dry overnight. Then we installed the two walls and applied pressure sticks between them, as shown. The sticks had foam on each end to keep from scratching the metal and to create a snug fit. Finally, I put in the screws and trim pieces, then installed the fixtures.


I hope this article will assist you in building your own stainless steel shower. I didn’t find much information out there so this was pretty much done on the fly. I’m pleased with the results and all the money we saved!


showerThanks for stopping by! Be sure to check out our bridge book. It includes some cool ideas that apply to other projects, like how to put a really tall post into a deep hole when you aren’t that tall. Here is the link: Building a Small Cable Suspension Bridge with the Cable Locking System

Images, diagrams, and text copyright 2015 by Marvin Denmark unless otherwise noted. Please do not copy and post my content anywhere without my permission. Thank you.

16 thoughts on “Building a Stainless Steel Shower Stall

  1. Hi,
    Thanks for this blog and advice. I found it while searching how to D.I.Y. a stainless steel shower. We are both pretty handy, and my bf is a trained carpenter. We are just hung up on the drain ‘dimple’. Is this just an indentation around the hole for the plug to sit in? I want to know exactly what to tell our metal guys. Thanks so much.

    • Glad you found my post! I couldn’t find much of anything about building these when I needed help, so was happy to share what I learned. As for the dimple, as written, “This was because the only shower drains I could find, locally and online, were for tile application. They set up higher than necessary for sheet metal. The dimple made it so the drain would set down low enough not to puddle.” So my suggestion is to buy your drain and give it to your fabricator so he can customize the hole. You’ve probably seen how some showers have a small ring of standing water around the drain after a shower, that’s the problem. I prefer that not to happen in our shower.

      Let us know how it goes!

  2. Hi, how much did your fabricator charge you for material and labor? We are renovating our 2006 New Horizon 5th wheel RV we just purchased. One of our projects projects will be a SS shower. We live in Oregon and should be able to find a fabricator in our area. Our shower is smaller than yours but a ball park price will give us an idea.

    • Sorry for the delay – the material and labor was $1600, as mentioned in the article. Maybe you can hire Mid Valley Metals as well, their link is in the blog. Good luck!

  3. Glad I could find you via Google! There’s still precious little info on a stainless enclosure…

    Now that you’ve lived with a bit, how has it been? Do you find it noisy? Anything you would do differently next time? Thanks!

    • Thanks for the comment, Joel. I’m happy with the shower after living with it for over a year. It’s not noisy at all, and pretty easy to maintain, a LOT easier than tile. I do wish I had triple-checked my measurements for the fabricator for the base, as I was off just a bit for the drain and that required some finessing that should not have been needed. But it’s all good now. I would not recommend the “heavy duty” metal suction cup shelves, soap holders, etc. as they hold up for a while, then BAM. Down they go. Usually in the middle of the night. I installed a floor-to ceiling stainless steel pole with shelf units and that looks and works much better.

  4. HI

    Could you possible post more pictures of the finished project. Also maybe some better detail pictures would be nice too. Thanks

    • Hi Dave, It’s tough to get a good photo in the small space, but I just posted a photo of the other side of the shower stall, it includes a shower caddy that I remodeled and put in the corner, works great. There is already a photo of the side with the fixtures. What details would you like to see? I’ll see if I have what you need here.

  5. First time home buyer…doing our first project… master bathroom remodel. I like modern and shiny. I thought it would be easy to find a solid, metallic shower base to go with the large shower wall tile we chose. We want to avoid the grout cleaning involved with tiled shower floors. I am surprised to see that stainless steel shower pans are so uncommon! I’m wondering why they aren’t popular? Does is scratch easy? Is it cold on your feet? Difficult to keep clean with soap scum? I’m not able to find any useful information online.

    • Michelle,

      I don’t think I have ever seen a stainless steel shower pan to match up with tile. You would have to have your’s manufactured. You will have to decide if you want the tile to go all the way to the floor of the pan or to land on a ledge before the pan floor level. Either way presents the same cleaning issues. The second choice is more expensive to make.

      Stainless pans aren’t popular because they are expensive. Plus they conjure up images of prison showers. Wow, what a contrast. To answer the other questions: no, doesn’t scratch easy; no, it doesn’t feel cold; no, it isn’t difficult to clean,

  6. Hi!
    What great information. We’ve just begun researching the idea of a stainless steel shower, or at the very least, a stainless shower pan, and we happen to live in Eugene. One question we have (and I surely may be back with more)is how are the joints of the wall panels caulked(made water-tight? Did you put any trim in the joints?

  7. Duh, I see the trim in the photos, that’s what I get for reading this out in the gorgeous sun. Would still appreciate knowing what you used to seal it up.
    Thanks again,

    • Cheryl,
      I’m not sure what you mean by seal it up. All the joints are overlapped with no need to seal. Do you mean how it was fastened to walls? I haven’t been able to find the name of the “glue”/product that I used to fastened the stainless steel to the wall, but there are several caulk like products capable of bonding the two. Make sure everything is clean.


    • Richard:
      To be honest, I didn’t specify the steel for the shower. That was left to the manufacturer as they had the expertise. They had done numerous counters and sinks and that would be comparable. But SS316 would probably be what they used from my limited knowledge regarding SS.

Leave a Reply to Dave Cash Cancel reply

Fill in your details below or click an icon to log in: Logo

You are commenting using your account. Log Out /  Change )

Google photo

You are commenting using your Google account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s